early_printk_console is enabled at 0x84000000
Ramdisk addr 0x2141092c, FDT 0x20a958b0
Found romfs @ 0x2141092c (0x002ec000)
#### klimit 202d3000 ####
Moving 0x002ec000 bytes from 0x2141092c to 0x202d2d5c
New klimit: 0x205bf000
Found FDT at 0x20a958b0
Linux version 2.6.26-rc9-mONStR-00393-g51fe2ed-dirty (monstr@seznam.cz) (gcc version 3.4.1 ( PetaLinux 0.20 Build -rc1 050607 )) #39 Thu Jul 24 17:12:21 CEST 2008
setup_cpuinfo: initialising
setup_cpuinfo: Using full CPU PVR support
setup_memory: max_mapnr: 0x30000
setup_memory: min_low_pfn: 0x20000
setup_memory: max_low_pfn: 0x10000
On node 0 totalpages: 65536
Normal zone: 512 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 65024 pages, LIFO batch:15
Movable zone: 0 pages used for memmap
Self modified code enable
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyUL0,115200
xlnx,xps-intc-1.00.a #0 at 0x81800000, num_irq=6, edge=0x0
PID hash table entries: 1024 (order: 10, 4096 bytes)
xlnx,xps-timer-1.00.a #0 at 0x83c00000, irq=1
Heartbeat GPIO at 0x81400000
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253824k/262148k available
Calibrating delay loop... 61.44 BogoMIPS (lpj=307200)
Mount-cache hash table entries: 512
net_namespace: 192 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Initializing RT-Tester: OK
msgmni has been set to 496
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
84000000.serial: ttyUL0 at MMIO 0x84000003 (irq = 5) is a uartlite
console [ttyUL0] enabled
brd: module loaded
nbd: registered device at major 43
eth0: using fifo mode.
eth0: No PHY detected. Assuming a PHY at address 0.
eth0: Xilinx EMACLite #0 at 0x81000000 mapped to 0x81000000, irq=3
uclinux[mtd]: RAM probe address=0x202d2d5c size=0x2ec000
Creating 1 MTD partitions on "RAM":
0x00000000-0x002ec000 : "ROMfs"
uclinux[mtd]: set ROMfs to be root filesystem index=0
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
Mounting proc:
Mounting var:
Populating /var:
Running local start scripts.
Mounting /etc/config:
Populating /etc/config:
flatfsd: Nonexistent or bad flatfs (-48), creating new one...
flatfsd: Failed to write flatfs (-48): No such device
flatfsd: Created 5 configuration files (185 bytes)
Mounting sysfs:
Setting hostname:
Setting up interface lo:
Setting up interface eth0:
Starting NFS:
Starting portmap:
Starting thttpd:
uclinux login: root
Password:
/*
* (C) Copyright 2007-2008 Xilinx, Inc.
* (C) Copyright 2007-2008 Michal Simek
*
* Michal SIMEK <monstr@monstr.eu>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
* CAUTION: This file is automatically generated by libgen.
* Version: Xilinx EDK 10.1.02 EDK_K_SP2.5
* Generate by FDT v1.00.a
* Project: /home/projects/fdt/trunk/hardware/user-platforms/ml505-mmu-fdt
*/
/dts-v1/;
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,microblaze";
model = "testing";
DDR2_SDRAM: memory@20000000 {
device_type = "memory";
reg = < 0x20000000 0x10000000 >;
} ;
chosen {
bootargs = "console=ttyUL0,115200";
} ;
cpus {
#address-cells = <1>;
#cpus = <1>;
#size-cells = <0>;
microblaze_0: cpu@0 {
clock-frequency = <125000000>;
compatible = "xlnx,microblaze-7.10.c";
d-cache-baseaddr = <0x20000000>;
d-cache-highaddr = <0x2fffffff>;
d-cache-line-size = <0x10>;
d-cache-size = <0x1000>;
device_type = "cpu";
i-cache-baseaddr = <0x20000000>;
i-cache-highaddr = <0x2fffffff>;
i-cache-line-size = <0x10>;
i-cache-size = <0x800>;
model = "microblaze,7.10.c";
reg = <0>;
timebase-frequency = <125000000>;
xlnx,addr-tag-bits = <0x11>;
xlnx,allow-dcache-wr = <0x1>;
xlnx,allow-icache-wr = <0x1>;
xlnx,area-optimized = <0x0>;
xlnx,cache-byte-size = <0x800>;
xlnx,d-lmb = <0x1>;
xlnx,d-opb = <0x0>;
xlnx,d-plb = <0x1>;
xlnx,data-size = <0x20>;
xlnx,dcache-addr-tag = <0x10>;
xlnx,dcache-always-used = <0x0>;
xlnx,dcache-byte-size = <0x1000>;
xlnx,dcache-line-len = <0x4>;
xlnx,dcache-use-fsl = <0x1>;
xlnx,debug-enabled = <0x1>;
xlnx,div-zero-exception = <0x1>;
xlnx,dopb-bus-exception = <0x0>;
xlnx,dynamic-bus-sizing = <0x1>;
xlnx,edge-is-positive = <0x1>;
xlnx,family = "virtex5";
xlnx,fpu-exception = <0x0>;
xlnx,fsl-data-size = <0x20>;
xlnx,fsl-exception = <0x0>;
xlnx,fsl-links = <0x0>;
xlnx,i-lmb = <0x1>;
xlnx,i-opb = <0x0>;
xlnx,i-plb = <0x1>;
xlnx,icache-always-used = <0x0>;
xlnx,icache-line-len = <0x4>;
xlnx,icache-use-fsl = <0x1>;
xlnx,ill-opcode-exception = <0x1>;
xlnx,instance = "microblaze_0";
xlnx,interconnect = <0x1>;
xlnx,interrupt-is-edge = <0x0>;
xlnx,iopb-bus-exception = <0x0>;
xlnx,mmu-dtlb-size = <0x4>;
xlnx,mmu-itlb-size = <0x2>;
xlnx,mmu-tlb-access = <0x3>;
xlnx,mmu-zones = <0x10>;
xlnx,number-of-pc-brk = <0x4>;
xlnx,number-of-rd-addr-brk = <0x2>;
xlnx,number-of-wr-addr-brk = <0x2>;
xlnx,opcode-0x0-illegal = <0x0>;
xlnx,pvr = <0x2>;
xlnx,pvr-user1 = <0x12>;
xlnx,pvr-user2 = <0x12345678>;
xlnx,reset-msr = <0x0>;
xlnx,sco = <0x0>;
xlnx,unaligned-exceptions = <0x1>;
xlnx,use-barrel = <0x1>;
xlnx,use-dcache = <0x1>;
xlnx,use-div = <0x1>;
xlnx,use-ext-brk = <0x1>;
xlnx,use-ext-nm-brk = <0x1>;
xlnx,use-extended-fsl-instr = <0x0>;
xlnx,use-fpu = <0x0>;
xlnx,use-hw-mul = <0x1>;
xlnx,use-icache = <0x1>;
xlnx,use-interrupt = <0x1>;
xlnx,use-mmu = <0x3>;
xlnx,use-msr-instr = <0x1>;
xlnx,use-pcmp-instr = <0x1>;
} ;
} ;
mb_plb: plb@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,plb-v46-1.03.a", "simple-bus";
ranges ;
Ethernet_MAC: ethernet@81000000 {
compatible = "xlnx,xps-ethernetlite-2.00.a";
device_type = "network";
interrupt-parent = <&xps_intc_0>;
interrupts = < 3 0x0 >;
local-mac-address = [ 02 00 00 00 00 00 ];
reg = < 0x81000000 0x10000 >;
xlnx,duplex = <0x1>;
xlnx,family = "virtex5";
xlnx,rx-ping-pong = <0x0>;
xlnx,tx-ping-pong = <0x0>;
} ;
LEDs_8Bit: gpio@81400000 {
compatible = "xlnx,xps-gpio-1.00.a";
interrupt-parent = <&xps_intc_0>;
interrupts = < 4 0x2 >;
reg = < 0x81400000 0x10000 >;
xlnx,all-inputs = <0x0>;
xlnx,all-inputs-2 = <0x0>;
xlnx,dout-default = <0x0>;
xlnx,dout-default-2 = <0x0>;
xlnx,family = "virtex5";
xlnx,gpio-width = <0x8>;
xlnx,interrupt-present = <0x1>;
xlnx,is-bidir = <0x1>;
xlnx,is-bidir-2 = <0x1>;
xlnx,is-dual = <0x0>;
xlnx,tri-default = <0xffffffff>;
xlnx,tri-default-2 = <0xffffffff>;
} ;
RS232_Uart_1: serial@84000000 {
clock-frequency = <125000000>;
compatible = "xlnx,xps-uartlite-1.00.a";
device_type = "serial";
interrupt-parent = <&xps_intc_0>;
interrupts = < 5 0x0 >;
port-number = <0>;
reg = < 0x84000000 0x10000 >;
xlnx,baudrate = <0x1c200>;
xlnx,data-bits = <0x8>;
xlnx,family = "virtex5";
xlnx,odd-parity = <0x0>;
xlnx,use-parity = <0x0>;
} ;
SysACE_CompactFlash: sysace@83600000 {
compatible = "xlnx,xps-sysace-1.00.a";
interrupt-parent = <&xps_intc_0>;
interrupts = < 2 0x2 >;
reg = < 0x83600000 0x10000 >;
xlnx,family = "virtex5";
xlnx,mem-width = <0x10>;
} ;
debug_module: debug@84400000 {
compatible = "xlnx,mdm-1.00.c";
reg = < 0x84400000 0x10000 >;
xlnx,family = "virtex5";
xlnx,interconnect = <0x1>;
xlnx,jtag-chain = <0x2>;
xlnx,mb-dbg-ports = <0x1>;
xlnx,uart-width = <0x8>;
xlnx,use-uart = <0x1>;
xlnx,write-fsl-ports = <0x0>;
} ;
mpmc@20000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,mpmc-4.02.a";
} ;
xps_intc_0: interrupt-controller@81800000 {
#interrupt-cells = <2>;
compatible = "xlnx,xps-intc-1.00.a";
interrupt-controller ;
reg = < 0x81800000 0x10000 >;
xlnx,num-intr-inputs = <0x6>;
} ;
xps_timer_1: timer@83c00000 {
compatible = "xlnx,xps-timer-1.00.a";
interrupt-parent = <&xps_intc_0>;
interrupts = < 1 0x2 >;
reg = < 0x83c00000 0x10000 >;
xlnx,count-width = <0x20>;
xlnx,family = "virtex5";
xlnx,gen0-assert = <0x1>;
xlnx,gen1-assert = <0x1>;
xlnx,one-timer-only = <0x0>;
xlnx,trig0-assert = <0x1>;
xlnx,trig1-assert = <0x1>;
} ;
} ;
} ;
