Xilinx SP605

• How to port U-BOOT
• How to port Linux
• How to load bitstream to PROM

• Xilinx
• http://www.xilinx.com/products/boards/s6embd/reference_designs.htm

Linux version 2.6.30-00048-g7755e67 (monstr@monstr.eu) (gcc version 4.1.2) #2 Fri Sep 25 16:06:57 CEST 2009
setup_cpuinfo: initialising
setup_cpuinfo: No PVR support. Using static CPU info from FDT
setup_memory: max_mapnr: 0x8000
setup_memory: min_low_pfn: 0x50000
setup_memory: max_low_pfn: 0x58000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c0246d94, node_mem_map c0830000
  Normal zone: 256 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line:  console=ttyS0,115200 
NR_IRQS:32
xlnx,xps-intc-1.00.a #0 at 0xfdfff000, num_irq=8, edge=0xffffff00
PID hash table entries: 512 (order: 9, 2048 bytes)
xlnx,xps-timer-1.00.a #0 at 0xfdffe000, irq=6
microblaze_timer_set_mode: shutdown
microblaze_timer_set_mode: periodic
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 121272k/131072k available
Calibrating delay loop... 31.68 BogoMIPS (lpj=63360)
Mount-cache hash table entries: 512
net_namespace: 520 bytes
NET: Registered protocol family 16
XGpio: /plb@0/gpio@81440000: registered
XGpio: /plb@0/gpio@81420000: registered
XGpio: /plb@0/gpio@81400000: registered
microblaze_timer_set_mode: oneshot
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
84000000.serial: ttyS0 at MMIO 0x84001003 (irq = 7) is a 16550A
console [ttyS0] enabled
Device Tree Probing 'ethernet'
xilinx_lltemac 81000000.ethernet: MAC address is now  0: a:35: 0:22: 1
xilinx_lltemac 81000000.ethernet: XLlTemac: using DMA mode.
XLlTemac: Dma base address: phy: 0x84600100, virt: 0xc803c100
XLlTemac: buffer descriptor size: 32768 (0x8000)
XLlTemac: Allocating DMA descriptors with kmalloc<6>XLlTemac: (buffer_descriptor_init) phy: 0x56c50000, virt: 0xc6c50000, size: 0x8000
XTemac: PHY detected at address 7.
eth0 (): not using net_device_ops yet
eth0: Dropping NETIF_F_SG since no checksum feature.
xilinx_lltemac 81000000.ethernet: eth0: Xilinx TEMAC at 0x81000000 mapped to 0xC8036000, irq=2
7c000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=255
erase region 1: offset=0x1fe0000,size=0x8000,blocks=4
RedBoot partition parsing not available
Creating 5 MTD partitions on "7c000000.flash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000060000 : "bootenv"
0x000000060000-0x000000080000 : "config"
0x000000080000-0x000000880000 : "image"
0x000000880000-0x000002000000 : "spare"
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Freeing unused kernel memory: 5952k freed
Mounting proc: 
Mounting var: 
Populating /var: 
Running local start scripts.
Mounting devpts:
Mounting /etc/config: 
Populating /etc/config: 
flatfsd: Created 4 configuration files (233 bytes)
Mounting sysfs:
Setting hostname: 
Bringing up network interfaces:
eth0: XLlTemac: Options: 0x3fa
eth0: XLlTemac: allocating interrupt 0 for dma mode tx.
eth0: XLlTemac: allocating interrupt 1 for dma mode rx.
eth0: XLlTemac: speed set to 100Mb/s
eth0: XLlTemac: Send Threshold = 24, Receive Threshold = 4
eth0: XLlTemac: Send Wait bound = 254, Receive Wait bound = 254
Starting portmap:

Xilinx-SP605-MMU-RTOS-11.3 login: root
Password: 

• FPGA: XC6SLX45T FGG484-2CES Spartan-6
• Configuration:
  • Onboard JTAG configuration circuitry
  • 128MB Platform Flash XL
  • Quad SPI Flash 64MB
  • 16MB Parallel (BPI) Flash
  • System ACE 2G Compact FLASH (CF) Card
  • JTAG
• Memory:
  • DDR3 Component Memory 1Gb
  • 16MB Parallel (BPI) Flash (Also available for configuration)
  • IIC 8Kb IIC EEPROM
• Communications and Networking
  • 10/100/1000 Tri-Speed Ethernet
  • SFP transceiver connector
  • GTX port (TX, RX) with four SMA connectors
  • USB To UART Bridge
  • PCI Express x1 Edge Connector
• Expansion Connectors:
  • FMC-LPC connector (1 GTP Transceiver, 68 single-ended or 34 differential user defined signals)
  • User GPIO with two SMA connectors
  • 4 User I/O (Digilent 2×6 Header)
• Clocking:
  • 200 MHz Oscillator (Differential)
  • Oscillator socket (Single-Ended)
  • SMA Connectors for external clock (Differential)
  • GTX Reference Clock port with 2 SMA connectors
• Display:
  • Video - DVI / VGA
  • 16×2 LCD character display
  • 4X LEDs
• Control:
  • 2X Push Buttons
  • 4X DIP Switches
• Power 12V wall adapter or ATX
• Voltage and Current measurement capability of 2.5V, 1.5V, and 1.2V, 1.0V supplies